Portable
Remote Control for Load-Haul-Dump Vehicles
Download
PDF Literature
The Cattron Group International AT16LHD and AT32LHD
portable remote control systems provide reliable, efficient and
convenient control of LHD equipment. This control system duplicates
the manual controls in the cab of the load-haul-dump, allowing the
operator to direct the equipment from a safer location.
System Features
- Designed to be mounted on high vibration
mining machinery
- AT16LHD incorporates 16 independent
functions, plus run on/off outputs
- AT32LHD offers up to 5 digital proportional
functions, plus up to 7 independent, as well as run. Systems also
available with custom PWM (pulse width modulation) configurations.
- Multiple watchdog circuits
- 2-digit system status display (acts
as a central test point)
- Automatic Safety Override (ASO)
output monitoring
- Addressing and time sharing to permit
multiple units to share each radio frequency
- Extremely high message security
- Extensive self diagnostics
- BCH data error
- Auto select 12-24 VDC input power
supply
- Compatible with Autodig™
- Optional joystick controller/transmitter
styles with fiberglass or aluminum dustproof, waterproof high
impact housings
- CE, FCC and Industry Canada approved
(contact the factory for information on other approvals)
Technical Specifications
Controller/Transmitters
 |
 |
| C01LHD |
P06C |
| Dimensions: |
C01LHD
- 15cmH x 35.5cmW x 9.5cmD (6 x 14 x 3 ¾ inches), weight approx.
5.5 kg (12 lbs.) including battery
P06C - 15cmH x 34.3cmW x 17cmD
(5.9 x 13.5 x 6.7 inches) weight approx. 4.2 kg (9 lbs.) including
battery |
Frequency Band: UHF
450 MHz to 470MHz (others available on request)
Standard RF Power Output: 20-40
mW output power (higher power available on request)
Spurious and Harmonic Emissions:
More than 33 db below carrier
Antenna: Internal
Modulation Digital Frequency: Shift
Keying (FSK)
Enclosure: C01LHD - Fiberglass
NEMA (4x), P06C - Aluminum
 LHD
Controller Harness
Receiver/Decoders
(AT16LHD and AT32LHD) 
| Dimensions: |
Approximately 30.5cmH
x 25.5cmW x 15cmD (12 x 10 x 6 inches) |
| Interface Type: |
AT16LHD - mechanical relays normally
open contacts 8A @250VAC or 5A @ 30VDC maximum
AT32LHD - proportional, current control with DDEC throttle control
interface. Optional custom PWM configurations available |
| Environment: |
Operate from -30ºC to +60ºC (-25ºF
to 140ºF), with non-condensing relative humidity from 0 to 95% |
| Output Termination: |
AT16LHD - 16 pin connector
(military specification)
AT32LHD - 24 pin connector (military specification)
Optional connector configurations available
|
| Enclosure: |
NEMA 4 steel (optional stainless
steel or fiberglass) Individual EMI - shielded compartments
for sub-chassis receiver, decoder and power supply. Entire sub-chassis
mounts on inside door of NEMA 4 enclosure. Relays not in sub-chassis. |
| Power requirements: |
12-24VDC ± 10% @ less than 2 amps,
± 20% @ less than 1 amp (12VDC), 24VDC (2 pin power connector)
for both AT16LHD and AT32 LHD |
For more details or specifications contact
your nearest Cattron-Theimeg office or representative. Specifications
subject to change without notice.
Autodig™ is a registered trademark
of Elphinstone |
